Serving the Rockford area  ·  (815) 420-4516  ·  Open Mon-Sun 7am-7pm
📞 (815) 420-4516 Free Quote

Metal Roofing in Rockford, IL (61101) · Local Professionals

Rockford Metal Roofing · Fast response in Rockford and the Rockford area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+345Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Rockford's older neighborhoods tell the story of this city in their rooflines. The steep gables of Haight Village Victorians, the dormered Swedish-heritage cottages on the east side, and the low-slung brick ranches out toward Alpine all sit under big silver maples and burr oaks along the Rock River, and every one of those roofs takes a beating from heavy snow, ice dams, and spring hail.

We are Rockford Metal Roofing, and we work these streets every week. From the Edgewater blocks to the North End, we have replaced shingles on American Foursquares, retrofitted standing seam over old decking, and chased down leaks that started at a chimney flashing and showed up three rooms away. If you are in 61101 or anywhere around Rockford, we know the housing stock and the weather that hits it.

Metal Roofing in Rockford (61101)

Rockford sits on both banks of the Rock River on glacial till and prairie soil, and that matters for roofing. The ground shifts with freeze-thaw cycles, old brick chimneys settle, and the heavy snow load that builds on steep Victorian roofs in Haight Village and Churchill Park is exactly where ice dams form at the eaves. Under all those mature maples and oaks, gutters clog fast, and a wet fall followed by a hard freeze can back water under shingles before you notice a stain on the ceiling. Out in the farm country around Rockford, corrugated panels on barns and pole buildings take wind and hail differently than a subdivision roof in Roscoe or Rockton, and we work both.

Our team has been on roofs across Winnebago County long enough to know which profiles work on a 1920s bungalow with dormers, which colors pass historic review near the Haight Village district, and how to detail flashing where a low-pitch ranch roof meets a brick wall. We install standing seam, metal shingle, stone-coated steel, and corrugated panels, and we repair the fasteners, seams, and flashing that fail first on older metal roofs.

Our services in Rockford

How a Job Works in Rockford

Step 1: You call us at (815) 420-4516 or send a request, and we set up a free on-site assessment. We walk the roof, check the attic and flashing details, and talk through whether repair, retrofit over your existing shingles, or a full replacement makes sense for your house and budget. You get a written estimate before anything starts.

Step 2: We pull the required roofing permit through the local building department and schedule the work. On tight lots in the older parts of Rockford, we plan material staging around alleys, driveways, and mature trees, and we coordinate with HOA design review where that applies. Crews protect landscaping and keep the site secure each night.

Step 3: We clean up thoroughly, haul away old material, and do a final walkthrough with you. We check gutters, downspouts, and every penetration, and we do not leave until you have seen the finished roof and understand the warranty.

Pricing in Rockford depends on roof size, pitch, access, and the condition of the deck and flashing. As a ballpark, metal roof installation starts around $8 per square foot, standing seam around $10, metal roof replacement around $9, and retrofit over existing shingles around $7. Corrugated and ribbed panel roofing starts near $5.50 per square foot, and metal shingle or stone-coated steel around $9. Repairs and leak calls start at $450, screw replacement and re-fastening at $750, flashing and chimney work at $600, and snow guards with ice protection at $1,200. Coating and painting starts around $2.50 per square foot, and gutters for metal roofs run about $9 per linear foot. Steep Victorian roofs, multiple layers of old shingles, and difficult access can raise the number, while a simple ranch roof keeps it lower. Call (815) 420-4516 for a free estimate on your Rockford property.

My Haight Village Victorian has a steep roof and ornate trim. Can you install metal without damaging the historic details?
Yes. We plan the install around the trim, cornices, and dormers that make those houses distinctive, and we use flashing details that fit the original roof lines. If your block falls under historic design review, we help you choose a panel profile and color that will pass, and we handle the permit process with the city.
A storm just peeled back panels on my roof in Rockford. How fast can you get out?
We treat wind-lifted panels and active leaks as priority calls. Call (815) 420-4516 and we will schedule a free inspection, tarp or secure the area if needed, and give you a repair plan. After a derecho or tornado-season squall, we work through the queue as quickly as we can and document damage for your insurance claim.
What does a typical metal roof cost for a ranch house in the North End?
A low-pitch ranch roof is usually one of the more straightforward jobs, so installation often lands near our starting rates, around $8 per square foot for standard metal and about $10 for standing seam. The final number depends on square footage, whether we remove old shingles, and the condition of the deck and flashing. We give you a firm written estimate after the free assessment.
Do I need a permit to replace my roof in Rockford, and who handles it?
Roofing permits are commonly required for a full replacement or re-roof in Rockford and the surrounding jurisdictions, and the rules, fees, and inspection requirements vary. We confirm the requirements with the local building department before work starts and pull the permit for you. You can also check general city information at the City of Rockford website.
My neighbor and I share a property line, and my new metal roof will shed snow toward their yard. What should I do?
Snow shedding is a real concern on metal roofs, and we can add snow guards to keep snow from sliding in one sheet. If the roofline is close to the property line, we review the setback and drainage with you, and if your subdivision has an HOA, we help coordinate the design review so the panel profile and color are approved before installation.
Are you insured for work on my Rockford property?
Yes, we are fully insured with general liability and workers' compensation coverage. We are happy to provide proof of insurance before work begins so you know your property and our crew are protected.
What maintenance should I do on a metal roof in Rockford before winter?
Clear leaves and debris from gutters and valleys, especially under the maples and oaks that drop heavily in fall. Check fasteners and seals on older panels, look for lifted flashing around chimneys and skylights, and make sure snow guards are secure before the first heavy snow. A quick inspection in late fall catches the small issues that turn into ice dams and leaks in January.
Why choose us?

Trusted professionals in Rockford

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Rockford

All your work handled by qualified professionals in Rockford

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

345+ Verified Client Reviews in Rockford

⭐⭐⭐⭐⭐ 4.9/5 · 345 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Rockford · Response within 24h · No commitment · ☎ (815) 420-4516

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Rockford ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm